Cannot create new folders under xplorer2 lite 1302

Ulrich Pamp · Post by **Ulrich Pamp** » 2005 Jul 24, 11:01

Hi there,

I cannot create new folders under 1302. An errormessage appears down left saying not possible to create new objects. Going back to 1201 all is ok. Tried this out for three times - always the same. I'm using W98.

Yours Ulrich

:?:

Post by **nikos** » 2005 Jul 24, 12:26

i can't think of any change that may have affected that
how are you creating folders, F8?
try a reboot

Ulrich Pamp · Post by **Ulrich Pamp** » 2005 Jul 25, 05:40

Yes, I used F8 und I did a reboot.
Unstall and install 1201 - all was ok. This cycle I tried a few times. Always the same result. With version 1302 F8 does not function.

Ulrich

jo · Post by jo » 2005 Jul 25, 05:56

I`m getting exactly the same problem, using windows XP. I tried reboot and runas with other admin account and rights. Nothing. Same error message . All other versions works fine.

Jo

narayan · Post by **narayan** » 2005 Jul 25, 08:29

Try changing disks and folders: Does it happen in all disks/folders or only in some places?

jo · Post by jo » 2005 Jul 25, 08:47

The error comes within local and network folders. The event viewer shows:

Event Type: Warning
Event Source: MRxSmb
Event Category: None
Event ID: 3019
Date: 25.07.2005
Time: 07:58:07
User: N/A
Computer: ITN01
Description:
The redirector failed to determine the connection type.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 04 00 4e 00 ......N.
0008: 00 00 00 00 cb 0b 00 80 ....Ë..
0010: 00 00 00 00 10 00 00 c0 .......À
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

Post by **nikos** » 2005 Jul 25, 08:59

are you both using translations perhaps? try removing the DLL to switch back to the english version of the program

wm44 · Post by **wm44** » 2005 Jul 25, 11:44

I got the same problem with the german version 1.3.0.2, after removing the files x2t_german.dll and x2t_deDE.dll and doing a reboot i can create folders again.

Werner

Post by **nikos** » 2005 Jul 25, 11:58

x2t_deDE.dll is a very old translation and could be the culprit
try reinstalling with the new translation dll (using the installer)
does it work properly?

jo · Post by jo » 2005 Jul 26, 06:08

Thanks to Niko and wm44 for the good hints to troubleshooting.
I delete the x2t_german.dll - 12.11.2004 - 120832 kB and it runs.
Normally I use only English versions, but probably I was a little bit confused by the Installation. :D

wm44 · Post by **wm44** » 2005 Jul 26, 09:23

Deleting all files in the x2-directory and reinstallation solved the problem.

Thanks for a good program and outstanding support.

Post by **nikos** » 2005 Jul 26, 09:24

that's good but is there a problem with the correct german translation? (the one that comes with 1302 installer)

jo · Post by jo » 2005 Jul 26, 13:29

It seems so. I installed the new version about the "old". I dont make an uninstall or delete any files before the installation of 1.3.0.2

wm44 · Post by **wm44** » 2005 Jul 26, 13:51

The german translation of 1.3.0.2 is working, but i don't know if it is correct.

Post by **nikos** » 2005 Jul 26, 13:57

i just tried it and it works properly (at least wrt F8 command)
each time you install a new version you'll have to remember to select your language too, else the old dll will be used with problems like those you observed